Adhesive film, etched glass design

  • glueless
  • Indoor assembly
Adhäsionsfolie i, Ätzglasdesign
Montagevideo starten
Außenansicht bei Nacht
Geometry Linear metre Roll
Rectangle
Square
Pentagon with slope
Rectangle with bevel
Rectangle with two slopes
symmetric trapezoid
right triangle
symmetrical triangle
Gable window
Rectangle with segmental arch
Rectangle with basket arch
Rectangle with semicircle
Quarter circle
Circle
Semicircle
Circle section
Oval / Ellipse
Available in the dimensions:
min. 5,0 x 5,0 cm
max. 98 x 2.500,0 cm
Width [cm]
Height [cm]
Cutting possible on request
Unfortunately, your desired size cannot be ordered via the online shop. However, we can still offer you the dimensions. Please ask our customer service at info@velken.shop.
from €1.00

Price per m² from: €27.90 Price per m²: €25.11 Price per m²: €23.99 incl. VAT plus shipping costs. Item no. 281020

Order accessories directly

Facilitates the installation of window films immensely! The films can be positioned on the glass without sticking. The concentrate is sufficient for an area of approx. 6m². The appropriate quantity is offered in the shopping basket.

Transfer concentrate
€3.49

This assembly set is suitable for smaller foil assemblies of up to 6m². In the set price you save over 15% compared to the individual components.

Mounting set
€8.95

This assembly set is ideal for medium-sized film installations of 5-10 m². With this bundle you save almost 23% compared to the individual components.

Assembly set professional
€14.95

Delivery time approx. 2-4 days

CNC cutting accurate to the millimetre

free assembly tool

Properties of this film
Protection from
Look
Privacy screen
high
Light transmission
high
Transparency
low
Design
without
Colour
white
Liability
glueless
Mounting side
Indoor assembly
Questionst?
Start WhatsApp chat
This film is a self-adhesive film without glue and is removable and reusable. It is removable...

This film is a self-adhesive film without glue and is removable and reusable. It is removable and reusable. Thanks to its very high light transmission, this privacy film is used in surgeries and wherever privacy needs to be protected.

In terms of decor, it is an opaque privacy film in an etched glass design (similar to a frosted glass film). Depending on the lighting conditions, only shadowy outlines are visible.
Due to the manufacturing process, this film may contain slight flow lines (stripes), which are no reason for complaint.
The adhesive strength of this self-adhesive privacy film is very high, so it is also suitable for wet rooms.

Shrinkage behaviour

Please note that this privacy film can shrink by up to 5% after you have removed it from the backing material. We therefore recommend that you adjust your film size accordingly when ordering. Before installation, peel the film off the backing and wait 30 minutes. During this time, the film will take on its final shape. You can then apply the adhesive film and carefully cut it to fit the glass with a cutter knife.
Complaints resulting from the shrinkage of the film are not grounds for complaint.

The scratch-resistant surface of the privacy film makes it easy to clean with standard glass cleaners. It is dirt-repellent and easy to clean.

Phthalate-free

Phthalates are chemical compounds that pose a health risk and can be found in plasticisers for plastics such as PVC. This privacy film is phthalate-free and therefore not affected!

Included in delivery

You should definitely order the transfer concentrate, art. no. 020010 additionally. It makes the installation easier and leads to a better result. Alternatively, you can also use a pH-neutral cleaner. This must be pH-neutral to prevent streaks from forming together with the film adhesive!

Any offcuts are not included in the scope of delivery.

Technical data and information at a glance...

Manufacturer's guarantee

The adhesive privacy film is a composite adhesive film made of PET and soft PVC. It is printable (screen printing, UV offset printing, UV digital printing) with a high UV resistance.

Depending on various factors, the durability and adhesive strength of the films for indoor installation are up to 10 years.

Technical data
Material PET and soft PVC
optical transparency slight flow lines
film thickness approx. 150 µm
adhesive static (without adhesive)
Dimensional stability maximum - 4% / + 1%
Temperature range -10° C to + 50° C
Phthalate-free yes

Mounting recommendation

Based on technical data and extensive experience, we can recommend mounting on the following vertically installed glass types:

Glass typeNumber of
panes
mainly
installed
U-value
W/(m²K)
Interior
installation
Single glazing 1 (-fold) until 1978 5,7 - 5,8 yes
Double glazing 2 (-fold)
2 (-fold)
3 (-fold)
1978 - 1994
1995 - Today
1978 - 1994
3.0 - 3.4
1.2 - 2.5
2.1 - 2.4
yes
yes
yes
Thermal insulation glazing 2 (-fold)
3 (-fold)
1978 - 1994
1995 - Today
1.7 - 2.1
0.4 - 1.4
yes
yes
Solar control glazing 2 (-fold)
2 (-fold)
3 (-fold)
1978 - 1994
1995 - Today
1995 - Today
1.4 - 2.0
1.0 - 2.5
0.5 - 1.3
yes
yes
yes

These recommendations may still result in glass breakage due to various factors at the installation site. According to our AGB, §10 paragraph 3 we do not accept any liability for this.

Answers to the most frequently asked questions...

General questions

Can I get a free foil sample?

Of course, please click on this link to access the corresponding order form. You are welcome to add to the list of items if you wish. There are no costs for you!

Will you also cut the film for me?

We cut each film to the exact millimetre according to the dimensions you enter. The cutting is free of charge. You can find detailed instructions on how to measure your panes here.

Alternatively, you can also cut your film by hand with a cutter knife. However, this requires a little manual skill, so you are usually better off using our free service.

Can you also cut a round blank or other geometry?

In general, almost all 2D shapes can be produced. Many geometries (e.g. triangles, trapezoids, circles) can be ordered directly via the online shop. To do so, please click on the orange rectangle to the right of the article image. You can then choose between many different shapes.

For shapes that are not specified, please send us a small sketch (photo) in which you specify the side lengths, radii or angles. Please contact us for this purpose.

Does the film also adhere to surfaces other than glass?

The window film adheres to all surfaces that are approximately as smooth as glass. When applying the film to plastic, please bear in mind that the adhesive may bond with the plastic, making it impossible to remove the film cleanly later.

How can I clean my window pane with the film in place?

You can keep your window pane clean as usual. The film should not be rubbed with sharp-edged objects (e.g. a brush).
You can find more information in our guide General care instructions for window films.

Can the film be removed without leaving any residue?

All window films can be removed without leaving any residue and without damaging the glass surface!
Below you will find detailed instructions on how to remove old window films.

Can you also print on films?

Unfortunately, we do not currently offer foil printing and do not have any partner companies with whom we can realise foil printing.

How to mount this film on the window...
Start assembly video
Installation video for window films. Click on the picture to start.

Assembly instructions for Adhesive films (glueless)

You will need the following items

Installation tips

  • Two people should carry out the installation!
  • Do not install any film at temperatures on the installation side below +6° C.
  1. Fill the spray bottle with 0.5 litres of water and add the transfer concentrate (30 ml) (enough for approx. 6 to 7 m² of glass surface).
  2. Thoroughly clean the glass with commercial or our glass cleaner!
    Remove all sticky particles (e.g. paint or fly dirt) preferably with the Glass scraper blade. No dirt residues should remain on the glass!
  3. The sandblasting foil consists of the mostly white backing paper and the actual sandblasting foil.
    Now place the sandblasting foil with the view side down on the glass pane or similar. You are now looking at the back of the film.
    Then carefully and slowly peel off the backing paper at as shallow an angle as possible until it is about halfway along the entire length of the film. Cut the backing paper and stick it back onto the sandblasting film with a gap of about 2 cm to the remaining backing paper.
  4. Now hold the Adhesive foils in place while the 2nd person peel off completely, starting from the corner.
    Note: Do not allow the backing paper to come into contact with water as this will cause irreparable contamination of the adhesive film.
  5. Afterwards, the glass pane (surface to be pasted) must be sprayed with the liquid. Do not be sparing with the liquid, film and pane should be well wet.
  6. Place the Adhesive foils on the glass, the film should slide back and forth well, otherwise spray the glass again.
  7. Now spray the other side of the Adhesive foils as well, this will make it easier for you to work with the mounting squeegee.
  8. Now press the liquid out evenly with the mounting squeegee from the centre to the right and to the left. Make sure that there is no residual water left under the film! Repeat this procedure several times to remove even invisible water residues. When doing this, wrap the supplied squeegee with a paper towel to avoid any scratches.
  9. Carefully wipe the edges and the foil with a soft cloth. If necessary, press the edges again with the mounting squeegee.
  10. Now let the Adhesive foils dry for three days without touching it.
  11. Wait two weeks before cleaning the film for the first time and never use hard objects (brush or blade) to clean it. Commercially available glass cleaners can be used.

FAQ`s about the installation

Can I carry out the film installation alone?

Films that are no larger than 1m² can be installed alone without any problems.
For larger pieces, it is recommended that two people carry out the installation. This makes it easier to handle the film and place it on the pane.

How can I avoid dust inclusions under the adhesive back side?

First, clean your windows really thoroughly with glass cleaner. Then go over the entire window pane again with our supplied Glass scraper blade to remove any hard-core impurities on the pane (such as fly droppings). These fine stains are often invisible to the naked eye and you will be amazed at what the blade still removes.

In addition, do not lay the Adhesive foils after peeling off (covers the adhesive side for transport) on the floor to get it wet. Rather, pull a table nearby to spray the film on. On the floor you will always stir up very fine dust particles, which will then settle on the adhesive side facing upwards. These dust particles can later show up on the pane under the Adhesive foils, which is something to avoid.

Can I apply the Adhesive foils without transfer concentrate?

Alternatively, you should at least use a pH-neutral cleaner. We do not recommend installation without any additive at all, which increases the gliding properties of the water!

We strongly advise against the use of water diluted with detergent. This can lead to streaking due to a reaction with the film adhesive.

Does the film have to be applied perfectly to the glass at the first attempt?

No, this is not necessary. The moisture makes it easy to move the film and position it precisely. Unlike self-adhesive films, you can always remove and reapply this adhesive film.

How easy is it to remove the film?

The window film itself can be easily removed. To do this, detach one corner and pull the film off the glass at as flat an angle as possible. No impurities will remain on the pane!
Order a product sample...

We will be happy to send you a free sample of this and up to four other films without obligation.
The samples are approx. 9 x 9 cm in size and will be sent to you free of charge and without obligation by letter post.

1. select sample (max. 5 pieces)
Adhesive film, etched glass design Adhesive film, etched glass design
Art.-Nr. 281020
Please select at least one sample!
2. Specify shipping address
Flat, floor, etc. (optional)
Germany
Here you can find our privacy policy.
Thank you very much!
We have received your foil requests.
The samples are usually sent to you within one working day.
Customer service

Expert adviser Thomas de Jong - Customer support

» Open questions about one of our articles? I'll be happy to answer them for you! «

Assembly instructions

Montagevideo starten
Installation video for window films. Click on the image to start.

Tool for easy assembly

The tool sets and accessories offered by Velken will be very useful for the success of your installation! Adhesive films, electrostatic films, decorative coatings... for each product there is the appropriate tool.

In addition to the assembly video, take a look at the detailed assembly instructions.

- 25 %
Assembly set professional
This assembly set is ideal for medium-sized film installations of 5-10 m². With this bundle you save almost 23% compared to the individual components.
040020 - Assembly set professional
€20.20 €14.95
Adhäsionsfolie Sandstrahldesign transparent matt
  • Indoor assembly
  • glueless
Privacy screen by day and night:
Light transmission:
€39.62 / m²
Adhäsionsfolie mit transparent weiß matten Blumen
  • Indoor assembly
  • glueless
Privacy screen by day and night:
Light transmission:
€37.82 / m²
Adhesive film, ribbed glass look (embossed)
  • Indoor assembly
  • glueless
Privacy screen by day and night:
Light transmission:
€37.82 / m²
Adhäsionsfolie mit transparenter Struktur
  • Indoor assembly
  • glueless
Privacy screen by day and night:
Light transmission:
€40.38 / m²
BESTSELLER
Order frosted glass film for windows as a made-to-measure privacy film
  • Indoor assembly
  • self-adhesive
Privacy screen by day and night:
Light transmission:
€26.84 / m²
- 25 %
Assembly set professional
Assembly set professional
€20.20 €14.95
- 27 %
Ein Montageset mit Sprühflasche, Filzrakel und Transferkonzentrat für perfekte Ergebnisse.
Mounting set
€12.30 €8.95
Cutter knife
Cutter knife
€2.95
- 27 %
Ein Montageset mit Sprühflasche, Filzrakel und Transferkonzentrat für perfekte Ergebnisse.
Mounting set
€12.30 €8.95
- 25 %
Assembly set professional
Assembly set professional
€20.20 €14.95
Adhäsionsfolie Frosted
Adhesive film, Frosted
€37.82 / m²
Questions about the item1
1 Question(s) in other languages.
Click here to view these question(s).
Question:
Guten Tag, ich möchte eine Scheibe halb auf der rechten Seite bekleben. Die Scheibe hat insgesamt eine Fläche von B127cm und H200cm.
Gibt es ein Problem mit der Wärmeentwicklung und damit eine Gefahr von Verspannung im Glas, wenn nur die Hälfte beklebt ist?
Mir ist mal eine vergleichbare Scheibe geplatzt, weil unten ein zusammengeklappter Umzugskarton angelehnt war und so für unterschiedliche Wärme auf dem Glas gesorgt hat.
Ulrich W. am 10. November 2022
Answer:
Bei weißen oder transparenten Fensterfolien besteht keine Gefahr vor Glasbruch. Die Folien absorbieren so wenig Sonnenenergie, dass sich keine nennenswerten Wärmespannungen in der Scheibe bilden.
Velken Service-Team on 10. November 2022
Compose reply
  Ask new question
Your question will be publicly visible and can - in addition to our support - also be answered by a member of our community.
Reviews 0
Be the first to rate this article!
Write a review now!
Last viewed